Wizzard 2.0 und Joyor F5 drosseln
Verfasst: Do 3. Jan 2019, 22:09
Der Wizzard 2.0 (auch vertrieben unter Johor F5) kann mit ein paar Klicks gedrosselt werden. Dazu im Settingsmode den Parameter P15 in Prozent entsprechend einstellen: 100% entsprechen 40km/h.
Alle weiteren Parameter:
P01: backlight brightness, 1 darkest, 3 lightest;
P02: mileage unit, 0: KM; 1: MILE;
P03: Voltage rating: 24V, 36V, 48V, default 36V;
P04: sleep time: 0, do not sleep;
other numbers for the sleep time, range: 1-60; unit minutes;
P05: Power-driven gear setting
P06: wheel diameter: unit, inch; precision: 0.1;
P07: Number of measuring magnets: Range: 1-100;
P08: speed limit Motor maximum speed
P09: zero start, nonzero start setting, 0: zero start; 1: nonzero start;
P10: Drive mode setting
0 Power drive
1 Electric drive
2 Power drive Electric drive coexistence
P11: boost sensitivity setting 1-24
P12: starting torque: range: 0-5,0 the weakest, 5 strongest;
P13: help plate magnet type setting ,5 8 12
P14: Controller current limit setting Default 12A
Range: 1-20A; (requires controller software support)
P15: Motor drive signal percentage setting
(to achieve PO8 speed limit function) Full speed is set to 100
P16: Instrument real-time cruise function 1 has this function
0 no such function
P17: headlamp synchronization function
1 after the start of the headlamps and backlighting is not lit
0 boot lights and backlighting
P18: Power-on password selection function
1 has this function ,0 no such function
P99: a key recovery function (in the P99 parameter settings interface, press and hold the MODE key for 5-6 seconds all the parameters to restore the first boot of the initial settings)
ODO: ODO clear (in the ODO parameter settings interface first press the MODE key and then press and hold 5M-6 seconds to zero)
Alle weiteren Parameter:
P01: backlight brightness, 1 darkest, 3 lightest;
P02: mileage unit, 0: KM; 1: MILE;
P03: Voltage rating: 24V, 36V, 48V, default 36V;
P04: sleep time: 0, do not sleep;
other numbers for the sleep time, range: 1-60; unit minutes;
P05: Power-driven gear setting
P06: wheel diameter: unit, inch; precision: 0.1;
P07: Number of measuring magnets: Range: 1-100;
P08: speed limit Motor maximum speed
P09: zero start, nonzero start setting, 0: zero start; 1: nonzero start;
P10: Drive mode setting
0 Power drive
1 Electric drive
2 Power drive Electric drive coexistence
P11: boost sensitivity setting 1-24
P12: starting torque: range: 0-5,0 the weakest, 5 strongest;
P13: help plate magnet type setting ,5 8 12
P14: Controller current limit setting Default 12A
Range: 1-20A; (requires controller software support)
P15: Motor drive signal percentage setting
(to achieve PO8 speed limit function) Full speed is set to 100
P16: Instrument real-time cruise function 1 has this function
0 no such function
P17: headlamp synchronization function
1 after the start of the headlamps and backlighting is not lit
0 boot lights and backlighting
P18: Power-on password selection function
1 has this function ,0 no such function
P99: a key recovery function (in the P99 parameter settings interface, press and hold the MODE key for 5-6 seconds all the parameters to restore the first boot of the initial settings)
ODO: ODO clear (in the ODO parameter settings interface first press the MODE key and then press and hold 5M-6 seconds to zero)